bit speed
英 [bɪt spiːd]
美 [bɪt spiːd]
网络 截割速度
双语例句
- I was going a bit over the speed limit, I'll have to admit.
我得承认，的确稍稍超过了速限。 - I think there's a bit more speed to be coaxed from these salls.
我想这些帆还能让我们更快点。 - A Low Bit High Speed A/ D Converter for a UWB Communication System
超宽带无线通信系统中低位宽超高速模数转换器的设计 - Ultra-Fast Optical Signal Encoding and Analysis for Communications and Data Fusion Networks; Final rept. 1 Apr 1996-31 Mar 1999 A Low Bit High Speed A/ D Converter for a UWB Communication System
超速光信号编码和分析用于通信和数据融合网络/最终报告超宽带无线通信系统中低位宽超高速模数转换器的设计 - They build a little more insulation along the wire, which adds a bit more bandwidth and precision to the circuit, which translates into an infinitesimal bit more skill and speed.
更宽、更精确的神经系统的电路会转化成无限小的技巧和速度的加快。 - The perfect performance of the DBS drilling rig extends life of drill bit, enhances drilling speed and makes the drilling work more secure and scientific.
DBS钻机性能优良，能延长钻头使用寿命，提高机械钻速，并使钻井更安全、科学。 - Cutting should have a good bit of speed and direction.
切割时应掌握好车刀的速度和方向。 - Bit speed is almost no influence on the torque.
钻头转速对钻头扭矩几乎无影响。 - The comparison between the computed and measured cone/ bit speed ratios proves that the assumption of minimum work is valid, therefore the simulation method can be used for appraising the cone/ bit speed ratio of roller bits.
仿真求得的轮体速比与实测值的对比结果证实最小功假设是可以成立的。用这一仿真试验方法能较好估计牙轮钻头的轮体速比值。 - Development of a 16-Bit High-Speed Digital-to-Analog Converter
一种16位高速D/A转换器的研究 - A 16-bit high-speed digital-to-analog converter is presented.
介绍了一种16位高速D/A转换器的电路设计、工艺制作和测试结果。 - The FG type anti-deviation device can operate under the normal bit weight and rotary speed.
FG型防斜工具可以在正常钻压及转速条件下钻进，并将井斜控制在较小的范围之内。 - A Monolithic 8 Bit High Speed Multiplying Digital to Analog Converter IC
一种单片8位高速乘法型D／A转换器 - Correting drilling mechanical rate through weight on bit, rotary speed and hydraulic parameters, the NDR ′ s affecting factors are only related to presure difference and formation, so that NDR can properly reflect formation drillability.
该方法从钻压、转盘转速、及水力学方面对钻井机械钻速进行校正，使其影响因素仅与压差和地层有关，从而使NDR能够正确反映地层的可钻性。 - On the basis of analysing drilling rate equation, mathematical models by which drilling time log data are utilized to calculate the bit initial drilling speed, V_0, and the decrease rate of drilling speed, φ, are put forward.
在分析钻速方程的基础上，提出了利用钻时录井资料计算钻头初始机械钻速V0和机械钻速下降率φ的数学模型。 - The analysis on experimental result shows that there is an optimum match between weight on bit and rotary speed to prevent hole inclination.
实验结果表明，在防料问题上也存在最优钻压-转速配合的问题。 - In this paper, a 12 bit high speed data acquisition system with computer aided testing parameters of self-scanning photodiode array ( SSPA-device) is introduced.
介绍用IBM－PC计算机辅助测试SSPA器件参数的12位高速数据采集系统。 - Research on 12 Bit 3M High Speed Data Acquisition System
12位3M高速数据采集系统的研制 - And the results are as follows: ( 1) According to the theoretical tooth face, the bit shift speed and acceleration expression are analyzed. And the necessity of modification is indicated.
根据波发生器端面凸轮的理论齿面方程，分析了活齿作直线往复运动时的位移、速度和加速度表达式，指出了对啮合副齿面进行修形的必要性。 - It is shown in tests that the waterjet-aided drill is running smoothly at the waterjet pressure of 1000-1400 bar and the bit rotation-speed of 300-400 rpm.
试验结果表明，该机及其钻头能在水射流压力为1000～1400巴、钻头转速为300～400转/分的情况下正常工作。 - DYL 8 Bit High Speed Video D/ A Converter Analysis and test
DYL多元逻辑八位高速视频D/A转换器分析与测试 - A monolithic 8 bit high speed digital to analog converter IC has been fabricated in Si bipolar process.
采用硅双极工艺制作了一种单片8位高速乘法型D／A转换器。 - The drive ratio of cone is less than 1 and is related to the axle tilt angle but basically not to the weight on bit and rotary speed.
牙轮传动比小于1，基本不受钻压和转速的影响，但与轴倾角有关。 - Taking the radial wear allowance of the bearing pair as the monitoring parameter of the bearing working status, and taking the rapid change of the bit speed and the working torque as the alarm signal, the trial of alarm technology for cone dropping is introduced.
文章介绍一种以轴承副的径向磨损量作为轴承工作状态监测参数、以钻头机械钻速和工作扭矩的急剧变化作为预警信号的牙轮脱落预警技术的试验研究成果。 - The rapid change of the bit speed and the working torque signals the end of the bit bearing life, and the bit should be changed.
钻头的机械钻速和工作扭矩急剧变化的信号预示钻头轴承寿命的终结，应该起钻更换钻头。 - The influence of rock, bit load and cone offset on cone/ bit speed ratio is investigated by simulation tests.
接着用软件试验探索岩石、钻压、移轴距对单齿圈牙轮钻头轮体速比的影响。 - The welding process can automatically run well according to setup of the technical parameters as segment numbers, length of segment, diameter of bit, welding speed and motor multiplicator.
系统具有按设置的刀头长度、刀头个数、钻头直径、焊接速度、电机倍频数等工艺参数进行自动焊接的功能。